Working Principle and Characteristic of RF Dryer



Liaoning Unify High-Frequency Equipment Co., Ltd. is a renowned Chinese welding machine supplier, we provide high frequency welding pvc, hf welder for sale, high frequency pvc welder, cardboard insulation and etc. Want to know more? Please contact us.





RF dryer is a kind of high efficiency leather drying equipment.



Working principle of RF Dryer

In the high-frequency electric field, the dielectric water in the wet leather will be affected by the electric field, causing molecular disturbance and friction and heat between molecules, so that the moisture in the leather will get enough heat and vaporize, and then the steam will be taken away by the air to achieve the purpose of leather drying.



Characteristics of high frequency drying

(1) The RF dryer working speed is fast because the electrical energy into heat, high frequency electric field and leather do not need any intermediary, so in the moment that leather is electrified, heat will produce, to achieve the purpose of rapid drying.



(2) Uniform drying, good leather quality if the leather dry to the specific moisture content, will encounter a lot of problems, one of them is the moisture uniformity problem. In the past, most tanneries have dried the leather to a leathery state and then rewetted it. It is said that only in this way can the leather have a uniform moisture content so that it can be tendered. The high frequency heating drying method is very different, the leather part of the absorption of heat is proportional to the moisture content of the part. As a result, the wet parts absorbed more heat energy, so that the moisture content of the whole skin became uniform. The traditional drying method can only carry out conventional drying, the wet parts retain more water, unless it is always drying, until all the water evaporation, so it is very easy to cause excessive drying and loss of area.



(3) Easy to operate, easy to control temperature, easy to achieve automation.



(4) High power consumption, gasification of 1kg of water about 8kW·h power.




评论

发表评论

此博客中的热门博文

Application of solid-state high frequency equipment in high frequency welded pipe production

图片
  The solid state hf welder  is different from the electron-tube high-frequency welding machine. The electron-tube radio frequency welding equipment has output welding transformer. The induction coil is installed on the secondary side of the welding transformer, which is easy to match. Solid state high frequency welding machine in addition to the low working voltage, at the same time slot way capacitance and induction coil, wear on the welding steel pipe resonant directly, because there was no welding, less level of coupling, significantly higher efficiency, and then the production of induction coil, strict and standard, make it match, due to the voltage at the same time, the low induction coil diameter and welding steel pipe diameter (the clearance of v-shaped opening) can be reduced, and it is one of the factors of improving the efficiency of welding. One thing is certain, the induction coil strict and the standard manufacture produces the benefit is far higher than the induction coi
阅读全文

How To Solve The Welding Problems Of PVC Membrane Welding Machine

图片
  At present, pvc membrane welding machine  has been widely promoted in a number of plastic welding industry. Various welding defects are inevitable in the process of use. In this article, it mainly analyzes how to solve the problems in debugging or welding.   1. Crush and bruise Pressing injury and abrasion are common problems in the process of hf pvc welder . Sometimes it's not so serious, and it just gets white or marks. When you encounter such problems, the first thing to do is to ensure that the location of the tooling is not out of alignment. First let off the air of the cylinder, press down the welding head, and carefully observe whether the welding head position of the scratch is correct. If the welding head is in the correct position, or if the abrasion or compression occurs on the support (or lower cover), then it is necessary to observe whether there is any interference between the tooling and the product. If it is old tooling, it is suggested to clean the tooling with a
阅读全文

HF Blister Packaging Welders

图片
  The HF blister welding machine  is an inexpensive option for creating packages that are durable, transparent, and tamper proof. We make a variety of shapes and can custom design a blister pack that will showcase your product in the best possible manner. Although we strive to provide our customers a very competitive price, we will not sacrifice quality to do so. All products are tested for clarity, wall thickness, and dimensional compliance before leaving our plant.   A clear plastic blister pack can be used in conjunction with a cardboard blister card to keep the product in full view for the customer to examine. The blister packaging is attached to the blister card through a heat-sealing process of high frequency blister sealing machine that allows the product to be displayed in a wide variety of methods. While this heat sealing process can be done with highly automated equipment, the use of blister packs is somewhat limited to light weight items. For heavier contents, a plastic clam
阅读全文